Sida 1 av 1

Stänga av bältespåminnare

Postat: ons jun 01, 2011 9:54 am
av Gixxer Rolle
Har precis köpt mig en Mondeo 2.0 TDCI 08 som jag är väldigt nöjd med dock retar jag mig på bältespåmminaren som för ett fasligt oväsen. Jag lyckades stänga av ljudet genom att göra följande.

Vrid på tändningen och när kontrollamporna slocknar sätter du i bältet och lossar det nio gånger (en gång = i och hur) inom 60 sekunder.

Detta innebär INTE att jag kör runt utan bälte!

Postat: ons jun 01, 2011 2:08 pm
av vr00mfondel
Detta måste jag testa då jag stör mig enormt på ljudet. Jag har alltid på mig bälte i trafiken, men kör ofta in och ut på jobbet utan bältet på och det är rätt rejäl volym på plingandet. Tack!

Postat: ons sep 07, 2011 7:43 am
av JesterHead
På min -06:a trycker man bara ner knappen som släpper bältet en gång så blir den tyst...

Postat: lör sep 10, 2011 8:26 pm
av MartinN
Jag hittade den här efter lite sökande:
Mk3

Remember

This only works on vehicles built from 4 February 2002. Before starting this procedure, make sure that: the handbrake's on, it's in Park or Neutral, the ignition is off, all doors are closed (and you're in the car), all the seatbelts are unbuckled and the headlamps are off.

Deactivating/Activating

Turn the ignition switch to position II. (Do not start the engine).
Wait until the safety belt warning indicator turns off. (Approximately one to two minutes). Note: The next 3 steps must be completed within 60 seconds or the procedure must be repeated.
Buckle then unbuckle the safety belt three times, ending with the safety belt unbuckled.
Turn the headlamps ON then OFF.
Buckle then unbuckle the safety belt three times ending with the safety belt unbuckled. After this step the safety belt warning indicator will be illuminated for three seconds.
Within seven seconds of the safety belt warning indicator turning off, buckle then unbuckle the safety belt. This will enable the belt minder if disabled or disable belt minder if enabled.

The following sequence will confirm the belt minder is enabled:

The safety belt warning indicator flashes four times per second for three seconds.
Three seconds with the safety belt warning indicator off.
The safety belt warning indicator flashes four times per second for three seconds again.

The safety belt warning indicator flashing four times per second for three seconds provides confirmation of belt minder disabled.

After confirmation, the deactivation/activation procedure is complete

Notes

1 If the vehicle doesn't have a seatbelt warning light, use the SRS (airbag) warning indicator instead.

2 If the seatbelt light doesn't normally come on until you move, proceed as above, without initially waiting for the belt warning indicator to go off (in this case, after the second three buckles, the indicator will flash a couple of times, instead of being illuminated for 3 seconds)
Funkar det inte så är ingen skada gjord.

stänga av bältesvarnare mondeo mk3 + mk4

Postat: fre sep 16, 2011 2:14 am
av henriq
gjorde detta på min mondeo 07 mk4 och funkar klockrent :)

http://www.fordwiki.co.uk/index.php?tit ... urning_Off

Postat: tor sep 17, 2015 4:10 pm
av mondeo
En gammal tråd nu, men hur aktiverar man bältespåminnaren igen då? Har precis köpt mig en Focus st 09, den påminner inte om bältet. För nog är det väl påminnare i den?

Postat: tor sep 17, 2015 5:43 pm
av Svennas
mondeo skrev:En gammal tråd nu, men hur aktiverar man bältespåminnaren igen då? Har precis köpt mig en Focus st 09, den påminner inte om bältet. För nog är det väl påminnare i den?
FRÅN http://workshop-manuals.com/ford/focus_ ... ctivating/

Deactivating/Activating
NOTE:
NOTE:Deactivation of the belt minder may also be carried out using WDS. Follow the instructions on the screen.
Turn the ignition switch to position II. (Do not start the engine).
The safety belt warning indicator will extinguish within 10 seconds.
NOTE:
NOTE:Step 3 must be completed within 60 seconds or the procedure must be repeated.
Buckle then unbuckle the safety belt nine times, ending with the safety belt unbuckled.
The safety belt warning indicator flashes three times to confirm the belt minder status change.
To activate the belt minder, repeat Steps 1 through 3.
After confirmation, the deactivation/activation procedure is complete.