Mondeo -96 1,6 16V Motorbytestrassel
-
Flupp
- Erfaren
- Inlägg: 95
- Blev medlem: tor feb 19, 2009 11:20 am
- Namn: Leif Löthberg
- Kör: Mondeo 1,6tdci 2011
Focus 2007 - Ort: Sandviken
Ja enligt ford så har alla bilar som har en röd nyckel pats eller om man har en svart med en röd markering! dom testade med en 93a box som jag var dit med men den gick inte pga att den inte hade pats...
Vad vill du ha för den då? har eg ingen plats jag heller har redan en 93 och en 94 står men kan ju ta dom grejor jag behöver och köra resten på skroten...
Har bes idag lördag27/2 och de gick som väntat!
CO 5,7
CO 2500 6,3
HC 530
LAMBDA 0,85
Vad vill du ha för den då? har eg ingen plats jag heller har redan en 93 och en 94 står men kan ju ta dom grejor jag behöver och köra resten på skroten...
Har bes idag lördag27/2 och de gick som väntat!
CO 5,7
CO 2500 6,3
HC 530
LAMBDA 0,85
- RickardEM
- Legend
- Inlägg: 7152
- Blev medlem: lör aug 23, 2003 10:00 am
- Namn: Rickard Ribbing
- Kör: Ka -97 & -10, Transit -98, 00, 01 & -09, Puma -20, Taunus -66, Fiesta -77 & -16, Granada -84, Escort -84
- Ort: Gyttorp
- Medlemsnummer: 56
Hittade detta, verkar inte så hoppfullt utan rätt nyckel dock...
PATS Programming:
Again depending on the year of your car you may or may not need to have PATS programmed to your module. PATS is the immobiliser system used by Ford to safeguard your car from being started with a fake key. It's wiring and operation is kept a close secret for obvious reasons however should you need to program a key here are the instructions.
PATS System I:
This system uses a solid RED master key KEY NUMBER SEVEN IN THE GUIDE without this key the system can not accept new keys and will need to be taken to ford. To program a new key:
* First insert your red master key in the ignition and turn to position II. When the control light (in clock/trip) illuminates turn the ignition off and remove the key.
* After approximately 2 seconds the control light illuminates again for a short period.
* When the control light goes out you have 10 seconds to program your new key.
* Insert the new key in the ignition and turn it to position II. The control light illuminates to indicate a successful programming operation.
* Remove the key.
PATS System II:
This system hasn't got a red key, instead it needs already programmed keys to access programming mode.
* Insert the first already programmed key into the ignition and turn to position II
* Turn back to 0 and remove the key
* Insert the second already programmed key into the ignition and turn to position II
* Turn back to 0 and remove the key
* Key programming mode is now activated and you have ten seconds to:
* Insert the unprogrammed new key into the ignition and turn to position II
* Turn back to 0 and remove the key
* Allow 10 seconds to pass for the system to exit programming mode.
PATS Programming:
Again depending on the year of your car you may or may not need to have PATS programmed to your module. PATS is the immobiliser system used by Ford to safeguard your car from being started with a fake key. It's wiring and operation is kept a close secret for obvious reasons however should you need to program a key here are the instructions.
PATS System I:
This system uses a solid RED master key KEY NUMBER SEVEN IN THE GUIDE without this key the system can not accept new keys and will need to be taken to ford. To program a new key:
* First insert your red master key in the ignition and turn to position II. When the control light (in clock/trip) illuminates turn the ignition off and remove the key.
* After approximately 2 seconds the control light illuminates again for a short period.
* When the control light goes out you have 10 seconds to program your new key.
* Insert the new key in the ignition and turn it to position II. The control light illuminates to indicate a successful programming operation.
* Remove the key.
PATS System II:
This system hasn't got a red key, instead it needs already programmed keys to access programming mode.
* Insert the first already programmed key into the ignition and turn to position II
* Turn back to 0 and remove the key
* Insert the second already programmed key into the ignition and turn to position II
* Turn back to 0 and remove the key
* Key programming mode is now activated and you have ten seconds to:
* Insert the unprogrammed new key into the ignition and turn to position II
* Turn back to 0 and remove the key
* Allow 10 seconds to pass for the system to exit programming mode.



